Bumble Bee Lesson 12



Written and Copyright KB Creations
This is my own creation, any similarities to other
tutorials is purely coincidental and unintentional.

In this part of the Lesson: Your doing the Same thing you
did on the previous lesson but your using different Tubes and patterns:
Look really close at my Finished Wizzard: You may even want to Right
click/ Save as and open him up in your A/S to get a close
look at each frame: I have 29 Frames in this one: That's a lot
of frames and would be heavy in an email but looks great
on a web Page: This would be something I would create to put on
the top of a Tourney page:

Good luck and have fun!

The supplies for this lesson were included with the supplies for Lesson 11.

 

Drag the Arrow to mark your progress





Step 1:   Open a New Image 800 x 800 Transparent background:

Step 2:   Your going to want to use a background on these because of
the Glar of the Sparkle: What I've done is use the same
tile for my background on my Tag that I used on my Web Page:
Those of you that are going to use this for a Web page
or Tourney page may want to do the same: For those of
you that will be using this for a Tag... You can use a color
of your choice and then frame it in when your finished:

Step 3:   Copy and Past the Wizard and place him at the bottom Left Corner:

Step 4:   Copy and Past the Misted Unicorm and place him behind the Wizard
in the Center:

Step 5:   Type in your Text using the Font and colors of your choice:
You want to make sure it's not a font that will stand
out to much.. It's going to work as your guide:

Step 6:   Copy and Past the Standing Bird in like this:

EXAMPLE: (I have resized the bird by 60%)


Step 7:   Copy and past the Flying Bird like this:

EXAMPLE: ( Resized by 60% )


Step 8:  

Please keep in mind you are the Artist: If you want to
move your Wizard to a Different place please do so: I'm just
here to guide you through another bling before you try to do
one Solo:


Step 9:   After you have everything in place Crop away the Extra:
( You want to do this now do that you don't crop off
any sparkles later:

Step 10:   Now Decide how you want your bling to Run and use your
Pen to draw it out: Try to see it in your mind:
Think of it as Tinker Bell from Petter Pan flying and spreding
her Pixie Dust around your Project:

EXAMPLE:


Step 11:   Close off Bird 1 ( The Standing Bird )

Step 12:   Activate the flying bird: go to Effects/ Illumination Effects/ Sunburst

Step 13:   Click and hold with your Left mouse botton on the Cross in
the First window and move it over the top of the bird:

SEE EXAMPLE:

IT WILL LOOK LIKE THIS:


PLEASE PAY CLOSE ATTENTION TO THIS PART:

Step 14:   Close off your Guide Line/ Text and Flying bird

Step 15:   Copy Merged and Past as a New Image in PSP

Step 16:   Rename this Frame 1

Step 17:   The Only change you will make for Frame 2 will be to Close
the Standing Bird and Open the flying Bird:

Step 18:   Copy Merged and Past into your New Image and Name it Frame 2:
( Notice how this Eliminates so much of the Layer Confussion: As you
finish each layer you can place them in order and work from there:)

Step 19:   Lower the Opacity on the Flying bird to about 50

Step 20:   Add a new Raster layer: This will hold your first Set of Sparkles:

Step 21:   Start Working in your Sparkles like this :

EXAMPLE: (Frame 3)

Notice that I have made my first Sparkle 250 over the Top
of my bird: This gives the Illusion that the birds turning into
the Sparkle and gives it the Magic:

Step 22:   Close off the Line and Text/ Copy Merged and Past as Frame 3

Step 23:   Add New Raster Layer: Name it Sparkles 2

Step 24:   Start working more Sparkles up your line:

EXAMPLE: (Frame 4)


From this point on I will be showing you Each Frame as I go:
Just keep following along:

FRAME 1

FRAME 2

FRAME 3

FRAME 4

FRAME 5

FRAME 6

FRAME 7

FRAME 8

FRAME 9

FRAME 10

FRAME 11

FRAME 12

FRAME 13

FRAME 14

FRAME 15

FRAME 16

FRAME 17

FRAME 18

FRAME 19

FRAME 20

FRAME 21

FRAME 22

FRAME 23

FRAME 24

FRAME 25

FRAME 26

FRAME 27


This one if ou look at it.. Was done different:


Step 25:   Once you get all your Layers Save each one as a JPEG

Step 26:   Using the Animation Wizard Load up all your Frames so you can
Animate it:( You learned how to use the Wizard in an earlier lesson )

Step 27:   Make sure you have all your frames in the right order:

Step 28:   View it : Do you need to change anything? Do you need to
set the Speed in your Frames?

Step 29:   If the Answer is no to Above: Resize and Save it:



Home Work

1) Turn in the one you made with this lesson

2) Be creative and try your hand using your own supplies and turn it in for credit



Click on the Button to the Right to return to the main Page
and the Button on the left to mail in all your Work:



Please do not copy, tear apart, email or share these lessons
without my permission: Thank You for your understanding and respect for
the hard work that goes into these lessons: